HOME     PRODUCTS     WEB STORE       PRODUCT CUSTOMIZATION       OEM/ODM     CONTACT   
     
    T200 18650 UPS + Power mgt Board HARDWARE   SOFTWARE
 
         
   
         
   
         
 
    SAFETY INSTRUCTIONS AND WARNINGS  
     
 
· You must read these safety instructions and warnings before charging your batteries. 
· Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the below instructions may result in fire, personal injury and damage to property if charged or used improperly. 
· Never make wrong polarity connection when charging and discharging battery packs. Always double check polarity of battery's connector to make sure "+" to "+" and "-" to "-". 
· Do not mix and use old batteries and new batteries, or batteries with different brand names. 
· Lithium batteries has it's cycle life, please replace old battery with new one when it reaches it's service life or when it is two year old, whichever comes first. 
· When charging Battery Pack, please put battery in a fire proof container. Please don't leave the X700 on the wood material or carpet and unattended. 
· Must keep the X700 away from children. 
 
     
    Product Overview 
     
FOR USE WITH
- Jetson Nano
OPERATING SYSTEM
- All operating systems
KEY FEATURES
   
  T200 18650 UPS + POWER MANAGEMENT BOARD
- Smart and powerful Uninterruptible Power Supply (UPS)
- Provides continuous operations for up to 10~30hours (depending on battery type and qty used)
- Max 5.1V 8000mA Power Backup for even the most demanding Jetson Nano set ups
- 18650 four Cells Lithium Ion Holder
- Can work with two or three or four 18650 Lithium Ion batteries
- Can work with T200-A1 battery stackable board - total battery capacity up to 38400mAh (12 18650 batteries)
- Supports 2A via micro-USB socket or 3A via DC jack fast charging
- Integrated battery protection circuit
- Integrated over current protection and over voltage protection
- Integrated Maxim's fuel-gauge systems (Reading battery voltage and percentage via i2c) - Cabling required
  Integrated TI's 10-A fully-integrated synchronous boost converter
- Intelligent automatic charging and discharging
- On-board 4 green LEDs indicate battery charging and discharging levels of 25%, 50% , 75% and 100%
- On-board blue LED show the status of power on/off
 
- Intelligent and safe power management
- On-board push button to control power on /off 
(Press-ON, Hold the button pressed at least 3s -OFF)
- Automatic powering off when system shutdown
- On-board pin header to enable auto power-on when power supplied or battery installed
- Ultra-low standby power consumption of μA to maximize battery life
- Operate in both charge mode and boost mode to allow full system management and battery power management
- Advanced system power path management avoids frequent charging and extend battery life
- Advanced system power path management allows 3A fast charging and powering Jetson Nano at the same time
- Powers the Jeton Nano via the onboard DC jack - Specially-made short DC cable supplied
- On-board DC power jack (5.5*2.5mm) and XH2.54 connector convenient for power input
- On-board PH2.0 connector allows to connect external power switch and DIY your perfect case
- On-board XH2.54 power output connectors allow to  power other devices
- Mounting holes and standoffs provide mechanical stability of the Jetson Nano and T200 assembly
   
T200-A1 18650 4-CELL BATTERY HOLDER
- 18650 four Cells Lithium Ion Holder
- Ideal solution to increase battery capacity (total battery capacity up to 38400mAh, 12 18650 batteries)
- Integrated battery protection circuit
- Mounting holes and standoffs provide mechanical stability of the Jetson Nano, T200 and T200-A1 assembly
   
SPECIFICATION
   
- Power supply via Micro-USB socket : 4.7~5.5Vdc, 2.5A
                              Via DC power jack : 4.7~5.5Vdc ±5%, ≥4A
- UPS output : 5.1V ±5% Max 8A
- UPS charging current: 2A via Micro-USB socket, 3A via DC jack
-

Terminal Battery Voltage : 4.2V
-

Recharge Threshold : 4.1V
   
NOTES
- Power path management active when applying power to the DC power jack
- Do not apply power to your Jetson Nano via the Micro USB socket.
- Do not use 18650 battery with built-in protection circuit
   
     
     
    Box Contents
 
       
- T200 18650 UPS + Power mgt Board x 1  
- DC cable Male to Male 15cm x 1  
- USB 3.0 A-Male to A-Male Data cable x 1  
- Spacer F/F M2.5 x 23mm x 4  
- Spacer M/F M2.5 x 9mm x 4  
- Screw M2.5 x 6mm x 4  
 
     
    Optional Accessories  
 
     
  Power Supply Unit  
- AC 100 - 240V input  
- 5Vdc 4A output
- W/ EU and US plug
- 5.5*2.5 DC plug
- 1.2M cable w/ magnet ring
  See details  
     
 
     
     
© 2019 SUPTRONICS TECHNOLOGIES LIMITED, ALL RIGHTS RESEVERED