Home     All DIY Kits     All Expansion Boards     Accessories     Web Store     OEM/ODM     Contact  
     
    Hardware Installation X10
     
 
❶ Required tool
  Screw diver 1 pc
 
❷ Required Accessories
  Spacer M2.5x20mm M/F 8 pcs
  Spacer M2.5x20mm F/F 4 pcs
  Screws M2.5x6mm 8 pcs
  RPI Power Cable 1 pc
  USB jumper board 1 pc
  Spacer M2.5x30mm M/F (Optional) 4 pcs For X10-HPAMP
  Audio cable (Optional) 1 pc For X10-HPAMP
               
❸ Push a screws (M2.5*6mm) up through the mounting hole on the underside of the Raspberry Pi.
 
❹  Screw the F-F spacer (M2.5*20mm) down until it is hand tight
     
     
❺ Optional Accessories
a) Place the X10-I2S board on top of Raspberry Pi and Screw the M-F spacer (M2.5*20mm) down until it is hand tight .

b) Remove the jumper link so it is powered by the R-core transformer.

 
❻ a) Plugs the DAC board straight into the X10-I2S' 40-pin header and Screw the M-F spacer (M2.5*20mm) down until it is hand tight .

b) Plugs the X10-PWR board straight into the DAC board's 12-pin header and screw down (M2.5*6mm screws).

c) Insert the USB bridge.
 
     
❼ Connect the power cable from X10-PWR board to Raspberry Pi pin header - Pin 4 (5V, Read wire) and Pin 6 (Ground, Black wire).
 
❽  IMPORTANT !!!
Connect the R-core transformer to the X10-PWR board
a) Make sure all ports on terminal block are open (Turn clockwise to tighten, counter-clockwise to loosen). 

b) Insert wires into the terminal block in the correct order.

C) Tighten down the screws the wires you have inserted. Try pulling each wire out of terminal block in order to insure that they are fastened securely.
 
 

White - White : 15VAC 0.55A
Yellow - Yellow : 15VAC 0.55A
Brown - Brown : 6VAC 0.5A
Grey - Grey : 6VAC 2.58A
     
❾ Power Supply Unit 35W R-CORE transformer

IMPORTANT !!!
AC voltage Selector
110V : AC input voltage MUST be 110~120VAC
220V : AC input voltage MUST be 220~230VAC

a) Make sure that you know what voltage is being supplied by the power outlet before setting the voltage selector switch and before connecting the power cord.

b) To switch the selection, unplug the power cord and use a small screwdriver to slide the switch to the opposite position.

 
❿ Before pressing the power button

a) All AC output wires to the X10-PWR board are wired in the correct order.

b) The power cable from X10-PWR board to Raspberry Pi pin header are correctly connected.

c) The AC input voltage selector switch are correctly switched.

     
⓫ Optional Accessories
Installing the X10-HPAMP headphone amplifier

a) Unplug the 12-pin extended header from X10-PWR.

b) Plugs the header straight into the X10-HPAMP board's 12-pin header




 
⓬ a) Plugs the X10-HPAMP board straight into the DAC board's 12-pin header and Screw the M-F spacer (M2.5*30mm) down until it is hand tight .

b) Plugs the X10-PWR board straight into the X10-HPAMP board's 12-pin header and screw down (M2.5*6mm screws). 

c) Connects the 3-pin audio cable from DAC board to X10-HPAMP board

d) Connect the power cable from X10-PWR board to Raspberry Pi pin header - Pin 4 (5V, Read wire) and Pin 6 (Ground, Black wire).

e) Install the volume knob with Allen Key M1.5
     
 
     
     
     
  © 2017 SUPTRONICS LIMITED, ALL RIGHTS RESEVERED