|
|
|
|
|
|
|
| |
| |
Enhance your Raspberry Pi 5 with effortless
installation and lightning-fast PCIe storage speeds!
Introducing the X1011-12V four M.2 NVMe SSD shield, designed
to provide a mass-capacity storage and high-speed storage
solution for your Raspberry Pi 5. Its sleek and
compact design enables easy attachment of four
full-size M.2 2280 SSDs to your Raspberry Pi 5. With
its PCIe 2.0 interface, you can experience data
transfer rates of up to 5Gbps, allowing you to
effortlessly transfer large amounts of data within
seconds.
The X1011-12V connects to the
underside of the Raspberry Pi 5, eliminating the
need for a passthrough for the GPIO. This means you
can use your favorite HATs while also utilizing this
expansion board.
The X1011-12V is an ideal storage solution for creating
a home media center or building a network-attached
storage (NAS) system. It allows you to store and
stream your own videos, music, and digital photos
within your home or even remotely across the world.
|
X1011 |
Power
input: 5V 5A,
Power
from Raspberry Pi5 through pogo pins or
onboard DC power jack |
|
X1011-12V |
Power input:
9-18V ≥3A, Power
from onboard DC power
jack |
|
|
|
| |
|
|
| |
| |
Compatible With
- Raspberry Pi 5B
- The perfect storage solution
for your Raspberry Pi 5 - the M.2 NVMe 4 SSD Shield
- Supports a total of 16TB storage capacity (4TB x4)
with M.2 NVMe solid-state drives
- Accommodates various M.2 NVMe SSD form factors,
including 2280, 2260, 2242, and 2230
- Provides speedy data transfer with PCIe 2.0 5Gbps
- LED indicators in blue display power and drive
status
- Features an integrated high-performance PCIe
packet switch
- Equipped with high-efficiency DC/DC step-down
converter, delivering a maximum of 12A to
power your SSDs
- Designed to be attached on bottom, allows using
your favorite HATs alongside it
- Compatible with the HAT+ STANDBY power state,
automatically turning off when the Pi 5 shuts down.
- Compatible with the official active cooler without
affecting cooling performance
* The
X1011-12V is designed specifically for data storage
purposes and does not currently support NVMe boot
with the existing firmware.
|
|
| |
|
|
| |
| |
Test Conditions
-System board details: Raspberry
Pi 5 Model B Rev 1.0 , 4G RAM
-Interface board details: X1011
v1.1 NVMe dual SSD Shield
-Operation system: Raspberry Pi
OS with desktop (Debian12 (bookworm), 64bit, Release
date: December 5th 2023)
-Storage details: Colorful CN600
120G,
Samsung PM961 120G, Netec N930E 120G, Silicon Power
P34A60 120GB
Testing disk drives read
speed at PCIe2.0 with hdparm
|
|
| |
|
|
| |
| |
|
Power supply |
: |
9-18Vdc +/-5% ≥3A power
via DC power jack, 12V ≥3A power supply
recommended |
|
Ports & Connectors |
: |
DC power jack:
5.5x2.1mm, polarity: center positive (+) |
|
|
|
PCIe connector x1 - 16-pin
pitch0.5mm |
|
|
|
SSD connectors x4 - M.2
KEY-M 67P |
|
PCIe FFC cable length |
: |
37mm |
|
PCB Size |
: |
109mm x 87.2mm |
|
|
| |
|
|
| |
| |
- X1011-12V V1.1 M.2 NVMe 4 SSD shield x1
|
| |
- PCIe FFC 37mm x1 |
| |
- Screw
pack x1 |
|
| |
|
|
| |
| |
|
- |
The
X1011 is designed specifically for data storage
purposes and does not currently support NVMe boot
with the existing firmware. |
|
- |
Compatible with M.2 NVMe SSDs |
|
- |
Not compatible with M.2 SATA SSDs, M.2 PCIe
AHCI SSDs, or other M.2 non-NVMe devices |
|
- |
Older NVMe drives with less efficient flash
media may not perform as well as newer
drives |
|
- |
New NVMe SSDs are not
partitioned and will need to be both
partitioned and formatted when first
connected to the Raspberry Pi before they
will be accessed in the Explorer. |
|
|
| |
|
|
