|
|
|
|
|
| |
| |
1 |
|
10-pin function header
- pin description |
|
| |
|
|
|
Functions |
Name |
PIN# |
PIN# |
Name |
Functions |
|
For eMMC programming |
nBOOT |
1 |
2 |
GND |
|
|
3.3V DC power |
3V3 |
3 |
4 |
5V0 |
5.0V DC power |
|
I2C data |
GPIO2 |
5 |
6 |
GND |
|
|
I2C clock |
GPIO3 |
7 |
8 |
GPIO14 |
UART0 TXD |
| |
GND |
9 |
10 |
GPIO15 |
UART0 RXD |
|
|
| |
|
|
|
|
| |
2 |
|
ATX control box header
- pin description |
|
| |
|
|
|
Functions |
Name |
PIN# |
PIN# |
Name |
Functions |
|
Control PC system reboot |
RST- |
1 |
2 |
RST+ |
Control PC system
reboot |
|
Control PC system power |
PWR- |
3 |
4 |
PWR+ |
Control PC system power |
|
Read the status of PC power LED |
HLED- |
5 |
6 |
HLED+ |
Read the status of PC
power LED |
|
Read the status of PC HDD LED |
PLED- |
7 |
8 |
PLED+ |
Read the status of PC
HDD LED |
|
|
|
| |
|
|
| |
| |
1 |
|
X652 IPKVM PCI manageemnt card
x1
|
|
2 |
|
Raspberry Pi Compute Module 4 x1
(all variants Compatible)
|
|
|
| |
3 |
|
16GB micro-SD card x1 (Required
for CM4 wihtout eMMC)
|
|
4 |
|
CR1220 coin battery x1 (For
Real-time clock)
|
|
|
| |
5 |
|
USB Type-C power supply (5V ≥
3A) x1
|
|
6 |
|
M.2 NVMe 2280 SSD (Optional, for
booting from SSD or storage expansion )
|
|
|
|
|
|
|
|
|
|
| |
|
|
| |
| |
1 |
|
Unplug all the cables that are
connected to the board. |
|
| |
|
|
|
|
| |
2 |
|
Install a Compute Module into the connector of the
Interface Board. Check that the Compute Module is
oriented correctly before fully inserting it into
the connector. Carefully align the two rows of
connectors and press together evenly to snap
together.
Caution:
Take static precaution measures when handling
the boards. |
|
|
|
|
|
| |
|
|
 |
|
| |
|
|
Confirm the Compute Module is
correctly mated by looking at each corner of the
Interface Board. 4 screw fixed hole are all
visiable.
|
|
| |
|
|
|
|
| |
3 |
|
Installing the CPU cooling fan
and insert the CR1220 coin battery (making sure that
the battery is oriented correctly. Positive side(+)
UP).
|
|
|
|
|
|
| |
|
|
 |
|
| |
|
|
|
|
| |
4 |
|
Insert the M.2 SSD into M.2 slot
then slide the SSD drive into the M.2 slot at 30
degrees while pushing it gently till it fits into
the slot. Notice that after insertion into the M.2
slot, the SSD drive inclined angle to the board.
finally press the M.2 SSD drive till it sits on the
riser screw then lock it in place using the M2
mounting screw.
|
|
|
|
|
|
| |
|
|
 |
|
|
| |
|
|
 |
| |
| |
1 |
|
Optional for testing and debug -
Connect the display for CM4 HDMI
video output using a miniHDMI to HDMI cable
|
|
2 |
|
Locat a HDMI port on your
PC/server and connect using a miniHDMI to HDMI cable
|
|
| |
|
|
|
|
|
|
| |
3 |
|
Locat an USB port on your
PC/server and connect using an USB-C to USB-A cable
|
|
4 |
|
Connect to an USB Type-C power
supply (5V ≥3A) |
|
| |
|
|
|
|
|
|
|
| |
5 |
|
Connect to your network using an
Ethernet cable |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
Important Notes
1. The pin assignments for the panel header may
differ by model. Refer to the motherboard user's
manual for the actual pin assignments.
2. HDD LED and Power LED need proper polarity
connection to funciton. Check your motherboard
manual for polarity requirements.
|
|
|
|
 |
|
|
| |
1 |
|
PC /server motherboard
|
|
2 |
|
Motherboard system panel
connector
|
|
|
|
|
|
|
|
|
|
|
| |
3 |
|
Plugs the ATX cable into
the box header and connects to motherboard system
panel header. |
|
4 |
|
Optional - Connect the Power
Switch wires, Reset Switch wires, HDD LED wires and
Power LED wires from front panel chassis connector
to the X650 box header (pinout printed on the board
bottom).
|
|
|
|
|
|
|
|
|
| |
|
|
Important Notes
1. The pin assignments for the panel header may
differ by model. Refer to the motherboard user's
manual for the actual pin assignments.
2. HDD LED and Power LED need proper polarity
connection to funciton. Check your motherboard
manual for polarity requirements.
|
|
| |
| |
How to install the PCI card |
|
|
| |
| |
1 |
|
Unplug your computer.
Power down your computer and then unplug the power
cable and all the other cables that are connected to
the back.
|
|
| |
|
|
| |
2 |
|
Open your computer.
PCI cards need to be installed inside your Computer's
chassis. |
|
| |
|
|
|
|
| |
3 |
|
Remove the metal bay
cover. Each PCI slot will have a bay
associated with it on the back of the computer. When
there's nothing installed, the bays are covered by
small metal protectors. You can remove one by
unscrewing the single screw holding it in place and
then lifting it directly out of the case. Set the
screw aside.
|
|
|
|
|
|
| |
|
|
 |
|
| |
|
|
|
|
| |
4 |
|
Gripping the PCI card by
the sides. Do not touch the contacts along the
bottom, and try to avoid touching any of the
circuitry.
|
|
|
|
|
|
| |
|
|
 |
|
| |
|
|
|
|
| |
5 |
|
Insert the card
and press it firmly straight down into the slot.
Ensure that the card is level and seated fully in
the slot before continuing. note that the X650 PCI
card is not required to insert into PCI slot on the
motherboard.
|
|
|
|
|
|
| |
|
|
|
|
| |
6 |
|
Secure the card.
Use the screw that you removed from the metal bay
cover and use it to secure the card into the same
hole. Tighten the screw firmly but not so tightly
that it will strip later.
|
|
|
|
|
|
| |
|
|
 |
|
| |
|
|
|
|
|
